1. Home
  2. Duct
  3. Return grille size

Return grille size Calculator

Free Return grille size Calculator. return (or supply) grille size from CFM, face velocity, and a free-area fraction. Runs in your browser; not a permit or a Manual J.

Updates in this browser · not a mechanical permit


Formula

Identity
A_free = Q / V_face; A_nominal ≈ A_free / free_area
Steps

Estimate only. Use the adopted mechanical code, nameplate curves and a licensed designer. Not Manual J, not a listed hood, not electrical sizing.

What this calculator does

This page converts return (or supply) grille size from CFM, face velocity, and a free-area fraction. It is the Return grille size tool in the duct group on ACH Calculator.

It is not a manufacturer NC catalog or a filter-rack CAD drawing. If you need those, open a related tool instead of stretching this identity.

The identity on screen is A_free = Q / V_face; A_nominal ≈ A_free / free_area. Adjacent pages keep their own inputs so you do not mix a bath-fan table with a 62.2 dwelling rate or a duct-friction takeoff.

Related calculators on this site:

How to use it

Use the fields that match the job: CFM, face FPM chips (300–500 return), free area % (e.g. 70%). Press Example to load the worked numbers. Clear empties the form. Related tools in the Next bar reuse CFM, ACH, temperatures and flows you already typed on this device.

Values update in this browser as you type. Use Example for the same numbers as the worked section. Copy puts the result on the clipboard. Next links reuse the last CFM, ACH and temperatures you typed on this device.

Formula, units, and limits

A_free = Q / V_face; A_nominal ≈ A_free / free_area

Reject zero or negative lengths, areas, flows, pressures and absolute temperatures. ACH above about 120 is allowed for tents and cleanrooms but is flagged as unusual for occupied rooms. The 1.08, 0.68, 500 and 24 factors assume near-standard air or water; override density when you are in Denver or on glycol.

Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.

When you would use it

Typical uses include:

1) 800 CFM return at 300 fpm, 70% free.

2) Filter grille with 50% free area.

3) Too-small return on a furnace.

If the job is life-safety, sterile, or listed equipment, stop here and use the specification.

None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.

Worked example

The Example button uses this set:

Q=800 CFM

V=300 fpm

A_free=2.67 ft²

70% → 3.81 ft² nominal ≈ 548 in²

Work the same arithmetic on paper; the live result should match within rounding.

FAQ

Face vs neck?

Face velocity uses the grille face. Neck velocity uses the duct collar — often higher.

Free area?

Blades and filters block area. 70% is a guess; use the submittal.

300 or 500 fpm?

Returns are quieter at the low end. Closet returns often run too fast.

Filter included?

A thick filter is extra ΔP on static-pressure, and may cut free area.

Multiple grilles?

Split CFM, then size each.

Supply registers?

Same identity; throw and spread are catalog data, not this.

References

Primary identity: A_free = Q / V_face; A_nominal ≈ A_free / free_area. Interpret it with the sources listed below, not as a photocopy of a copyrighted table.

  • ASHRAE Standard 62.1 and 62.2 — outdoor-air and dwelling-ventilation forms (overview of published identities; tables remain in the licensed standard).
  • International Mechanical Code — residential bath/kitchen exhaust discussion values commonly implemented as 50/20 CFM; confirm the adopted year.
  • ASHRAE Fundamentals — moist-air relations, duct fitting concepts, fan laws, hydronic constants 500 and 1.08.
  • ISO 14644-1 — cleanroom classification names (particle limits, not a mandatory ACH).
  • Magnus / WMO saturation vapor-pressure approximations for dew point.
  • Huebscher equivalent-diameter relation for rectangular ducts.

Disclaimer

Estimate only for Return grille size. Adopted mechanical codes, OEM curves and a licensed designer prevail.

Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size refrigerant charge, fire dampers, medical gas, or electrical conductors.