Free Air density Calculator. moist or dry air density from temperature, pressure or altitude so 1.08 and fan power stay honest. Runs in your browser; not a permit or a Manual J.
Estimate only. Use the adopted mechanical code, nameplate curves and a licensed designer. Not Manual J, not a listed hood, not electrical sizing.
This page converts moist or dry air density from temperature, pressure or altitude so 1.08 and fan power stay honest. It is the Air density tool in the duct group on ACH Calculator.
It is not a full ASHRAE psychrometric chart reprint. If you need those, open a related tool instead of stretching this identity.
The identity on screen is ρ = P / (R T) dry air; optional altitude → P. Adjacent pages keep their own inputs so you do not mix a bath-fan table with a 62.2 dwelling rate or a duct-friction takeoff.
Related calculators on this site:
Use the fields that match the job: DB temperature, altitude or P, optional RH for moist density. Press Example to load the worked numbers. Clear empties the form. Related tools in the Next bar reuse CFM, ACH, temperatures and flows you already typed on this device.
Values update in this browser as you type. Use Example for the same numbers as the worked section. Copy puts the result on the clipboard. Next links reuse the last CFM, ACH and temperatures you typed on this device.
ρ = P / (R T) dry air;
Reject zero or negative lengths, areas, flows, pressures and absolute temperatures. ACH above about 120 is allowed for tents and cleanrooms but is flagged as unusual for occupied rooms. The 1.08, 0.68, 500 and 24 factors assume near-standard air or water; override density when you are in Denver or on glycol.
Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.
Typical uses include:
1) Denver vs sea level.
2) Replacing 0.075 lb/ft³.
3) Sensible coefficient 1.08 × ρ/0.075.
If the job is life-safety, sterile, or listed equipment, stop here and use the specification.
None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.
The Example button uses this set:
T=70 °F
sea level
ρ ≈ 0.075 lb/ft³
Work the same arithmetic on paper; the live result should match within rounding.
Standard air ≈ 0.075 lb/ft³. The 1.08 factor is 60/13.5×0.24×0.075-ish. At altitude, 1.08 is high.
Water vapor lowers density slightly. Toggle RH.
Open the altitude-density chart for a quick look, then type a precise T.
kg/m³; R_specific ≈ 287 J/kg·K for dry air.
Irrelevant. This is static density.
scfm-acfm, sensible-heat.
Primary identity: ρ = P / (R T) dry air; optional altitude → P. Interpret it with the sources listed below, not as a photocopy of a copyrighted table.
Estimate only for Air density. Adopted mechanical codes, OEM curves and a licensed designer prevail.
Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size refrigerant charge, fire dampers, medical gas, or electrical conductors.