1. Home
  2. Air
  3. Cleanroom ACH

Cleanroom ACH Calculator

Free Cleanroom ACH Calculator. cleanroom supply CFM from a user-selected air-change target associated with an ISO class name. Runs in your browser; not a permit or a Manual J.

Updates in this browser · not a mechanical permit


Formula

Identity
CFM = ACH × V / 60 with ACH from a user ISO-class chip or custom
Steps

Estimate only. Use the adopted mechanical code, nameplate curves and a licensed designer. Not Manual J, not a listed hood, not electrical sizing.

What this calculator does

This page converts cleanroom supply CFM from a user-selected air-change target associated with an ISO class name. It is the Cleanroom ACH tool in the air group on ACH Calculator.

It is not a copy of ISO 14644 particle limits, a GMP protocol, or a hospital OR pressure cascade. If you need those, open a related tool instead of stretching this identity.

The identity on screen is CFM = ACH × V / 60 with ACH from a user ISO-class chip or custom. Adjacent pages keep their own inputs so you do not mix a bath-fan table with a 62.2 dwelling rate or a duct-friction takeoff.

Related calculators on this site:

How to use it

Use the fields that match the job: Room volume, ISO class chip (maps to an editable ACH), HEPA coverage optional note. Press Example to load the worked numbers. Clear empties the form. Related tools in the Next bar reuse CFM, ACH, temperatures and flows you already typed on this device.

Values update in this browser as you type. Use Example for the same numbers as the worked section. Copy puts the result on the clipboard. Next links reuse the last CFM, ACH and temperatures you typed on this device.

Formula, units, and limits

CFM = ACH × V / 60 with ACH from a user ISO-class chip or custom

Reject zero or negative lengths, areas, flows, pressures and absolute temperatures. ACH above about 120 is allowed for tents and cleanrooms but is flagged as unusual for occupied rooms. The 1.08, 0.68, 500 and 24 factors assume near-standard air or water; override density when you are in Denver or on glycol.

Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.

When you would use it

Typical uses include:

1) ISO 7 lab at 30–60 ACH as a user pick.

2) ISO 8 packing at 15–25 ACH.

3) Custom 20 ACH on a 20×20×10 ft room.

If the job is life-safety, sterile, or listed equipment, stop here and use the specification.

None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.

Worked example

The Example button uses this set:

20×20×10 = 4000 ft³

ACH = 30

CFM = 2000

Work the same arithmetic on paper; the live result should match within rounding.

FAQ

Is this ISO 14644?

ISO 14644-1 defines particle concentrations, not a mandatory ACH. ACH chips are industry planning ranges you can edit.

Unidirectional vs mixed?

ISO 5 unidirectional is often specified as face velocity, not ACH. Use capture/face tools.

Filter coverage?

Ceiling coverage and ACH both appear in older FS-209-style talk. This page only converts ACH × volume.

Recovery time?

Not calculated. Recovery depends on ACH and mixing, measured in the empty room.

Hospital OR?

OR specs use pressure, ACH, and filtration from guidelines (e.g. FGI/ASHRAE 170) — different from ISO class chips.

Why so much CFM?

30 ACH on a large room is a lot of air. Duct and fan tools come next.

References

Primary identity: CFM = ACH × V / 60 with ACH from a user ISO-class chip or custom. Interpret it with the sources listed below, not as a photocopy of a copyrighted table.

  • ASHRAE Standard 62.1 and 62.2 — outdoor-air and dwelling-ventilation forms (overview of published identities; tables remain in the licensed standard).
  • International Mechanical Code — residential bath/kitchen exhaust discussion values commonly implemented as 50/20 CFM; confirm the adopted year.
  • ASHRAE Fundamentals — moist-air relations, duct fitting concepts, fan laws, hydronic constants 500 and 1.08.
  • ISO 14644-1 — cleanroom classification names (particle limits, not a mandatory ACH).
  • Magnus / WMO saturation vapor-pressure approximations for dew point.
  • Huebscher equivalent-diameter relation for rectangular ducts.

Disclaimer

Estimate only for Cleanroom ACH. Adopted mechanical codes, OEM curves and a licensed designer prevail.

Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size refrigerant charge, fire dampers, medical gas, or electrical conductors.