Free CADR air changes Calculator. air-cleaner air changes from AHAM-style CADR and room volume (or the reverse CADR need). Runs in your browser; not a permit or a Manual J.
Estimate only. Use the adopted mechanical code, nameplate curves and a licensed designer. Not Manual J, not a listed hood, not electrical sizing.
This page converts air-cleaner air changes from AHAM-style CADR and room volume (or the reverse CADR need). It is the CADR air changes tool in the air group on ACH Calculator.
It is not a HEPA medical claim, wildfire IAQ advice, or a whole-house ERV rate. If you need those, open a related tool instead of stretching this identity.
The identity on screen is ACH = CADR × 60 / Volume (CADR in cfm). Adjacent pages keep their own inputs so you do not mix a bath-fan table with a 62.2 dwelling rate or a duct-friction takeoff.
Related calculators on this site:
Use the fields that match the job: Room volume, CADR (smoke/dust/pollen — you type one number), result ACH or required CADR. Press Example to load the worked numbers. Clear empties the form. Related tools in the Next bar reuse CFM, ACH, temperatures and flows you already typed on this device.
Values update in this browser as you type. Use Example for the same numbers as the worked section. Copy puts the result on the clipboard. Next links reuse the last CFM, ACH and temperatures you typed on this device.
ACH = CADR × 60 / V;
Reject zero or negative lengths, areas, flows, pressures and absolute temperatures. ACH above about 120 is allowed for tents and cleanrooms but is flagged as unusual for occupied rooms. The 1.08, 0.68, 500 and 24 factors assume near-standard air or water; override density when you are in Denver or on glycol.
Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.
Typical uses include:
1) 300 cfm CADR in a 1500 ft³ room → 12 ACH.
2) Target 5 ACH, solve CADR.
3) Comparing two purifiers.
If the job is life-safety, sterile, or listed equipment, stop here and use the specification.
None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.
The Example button uses this set:
15×12×8 = 1440 ft³
CADR = 200 cfm
ACH = 200×60/1440 = 8.3; CADR for 5 ACH = 120 cfm
Work the same arithmetic on paper; the live result should match within rounding.
AHAM CADR has smoke, dust, pollen. Use the pollutant you care about; they differ.
Convert: 1 CFM ≈ 1.699 m³/h. The identity is still Q × 60 / V for ACH.
Public-health sketches during wildfire/virus talk often use CADR to hit a target ACH. This is mixing, not a medical device.
Short-circuiting reduces effective ACH. The formula assumes well-mixed air.
MERV filters on a furnace are not CADR-rated the same way. Do not paste a MERV number into CADR.
Not modeled. Higher CADR often means a higher fan tap.
Primary identity: ACH = CADR × 60 / Volume (CADR in cfm). Interpret it with the sources listed below, not as a photocopy of a copyrighted table.
Estimate only for CADR air changes. Adopted mechanical codes, OEM curves and a licensed designer prevail.
Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size refrigerant charge, fire dampers, medical gas, or electrical conductors.