1. Home
  2. Air
  3. Bathroom fan CFM

Bathroom fan CFM Calculator

Free Bathroom fan CFM Calculator. a residential bathroom exhaust rate using the IMC-style 50/20 CFM chips or a volume×ACH check. Runs in your browser; not a permit or a Manual J.

Updates in this browser · not a mechanical permit


Formula

Identity
required = max(50 CFM, HVI area or fixtures, V×8/60)
Steps

Estimate only. Use the adopted mechanical code, nameplate curves and a licensed designer. Not Manual J, not a listed hood, not electrical sizing.

What this calculator does

This page converts a residential bathroom exhaust rate using the IMC-style 50/20 CFM chips or a volume×ACH check. It is the Bathroom fan CFM tool in the air group on ACH Calculator.

It is not ASHRAE 62.2 whole-house ventilation, a kitchen hood, or a makeup-air balance for the whole dwelling. If you need those, open a related tool instead of stretching this identity.

The identity on screen is required = max(50 CFM code floor, HVI 1 CFM/ft² or fixtures, 8 ACH). Adjacent pages keep their own inputs so you do not mix a bath-fan table with a 62.2 dwelling rate or a duct-friction takeoff.

Related calculators on this site:

How to use it

Use the fields that match the job: length, width, height, toilets, showers, tubs and jetted tubs. Press Example to load the worked numbers. Clear empties the form. Related tools in the Next bar reuse CFM, ACH, temperatures and flows you already typed on this device.

Room L×W×H, toilets, showers, tubs, jetted tubs. Result is the largest of IRC 50 CFM, HVI area/fixture, and 8 ACH.

Values update in this browser as you type. Use Example for the same numbers as the worked section. Copy puts the result on the clipboard. Next links reuse the last CFM, ACH and temperatures you typed on this device.

Formula, units, and limits

required = max(50 CFM, HVI area or fixtures, V×8/60)

Reject zero or negative lengths, areas, flows, pressures and absolute temperatures. ACH above about 120 is allowed for tents and cleanrooms but is flagged as unusual for occupied rooms. The 1.08, 0.68, 500 and 24 factors assume near-standard air or water; override density when you are in Denver or on glycol.

Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.

When you would use it

Typical uses include:

1) A 5×8×8 ft powder room checking that 50 CFM is more than 8 ACH.

2) A basement bath with a long duct where 50 CFM nameplate may not arrive.

3) A continuous 20 CFM Panasonic-style fan versus a 50 CFM switch-on fan.

If the job is life-safety, sterile, or listed equipment, stop here and use the specification.

None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.

Worked example

The Example button uses this set:

10×8×8 ft bath, 1 toilet + 1 shower

HVI area 80 CFM, 8 ACH ≈ 85 CFM, code floor 50 → required 85 CFM, buy 110

Work the same arithmetic on paper; the live result should match within rounding.

FAQ

Is 50 CFM a law on this page?

No. 50 CFM intermittent and 20 CFM continuous are widely adopted IMC table values for a residential bath. Your adopted code year and local amendments win.

Intermittent or continuous?

Intermittent is a switch-operated fan sized near 50 CFM. Continuous is a low-sone always-on fan near 20 CFM. Do not add them unless the design says so.

Does 50 CFM include the duct?

Nameplate CFM is at a test pressure. Elbows, roof caps and long runs cut delivered CFM. Open static pressure / fan-actual.

Can I size by ACH instead?

Yes. Some designers want 8 ACH on a large bath. Compare that CFM with the 50/20 chips.

Toilet only versus shower?

IMC treats a dwelling bath as one room for the table. A shower with a glass door still usually uses the same 50/20 unless the spec says otherwise.

Do I need makeup air?

A single 50 CFM bath fan rarely does. Stack several baths plus a range hood and open the makeup-air tool.

References

Primary identity: Intermittent ≈ 50 CFM; continuous ≈ 20 CFM; or CFM = ACH × V / 60. Interpret it with the sources listed below, not as a photocopy of a copyrighted table.

  • ASHRAE Standard 62.1 and 62.2 — outdoor-air and dwelling-ventilation forms (overview of published identities; tables remain in the licensed standard).
  • International Mechanical Code — residential bath/kitchen exhaust discussion values commonly implemented as 50/20 CFM; confirm the adopted year.
  • ASHRAE Fundamentals — moist-air relations, duct fitting concepts, fan laws, hydronic constants 500 and 1.08.
  • ISO 14644-1 — cleanroom classification names (particle limits, not a mandatory ACH).
  • Magnus / WMO saturation vapor-pressure approximations for dew point.
  • Huebscher equivalent-diameter relation for rectangular ducts.

Disclaimer

Estimate only for Bathroom fan CFM. Adopted mechanical codes, OEM curves and a licensed designer prevail.

Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size refrigerant charge, fire dampers, medical gas, or electrical conductors.