1. Home
  2. Air
  3. Dryer exhaust and makeup

Dryer exhaust and makeup Calculator

Free Dryer exhaust and makeup calculator. Add dryer + hood + baths that can run together; flag makeup when the hood > 400 or the dryer > 200 CFM. Runs in your browser; not a permit or a Manual J.

Updates in this browser · not a mechanical permit


Formula

Identity
Q_tot = dryer + hood + baths; makeup ≈ Q_tot if hood>400 or dryer>200
Steps

Estimate only. Use the adopted mechanical code, nameplate curves and a licensed designer. Not Manual J, not a listed hood, not electrical sizing.

What this calculator does

Ranking makeup inventories all add simultaneous exhaust: clothes dryer at a 150 CFM planning default (the 100–225 band they cite), plus the hood high speed, plus baths that can run with them. Residential hood talk still starts at 400 CFM; dryer talk starts at 200 CFM. This page sums the three and, if either trigger is crossed, reports makeup equal to the sum — the conservative IRC-family reading already used on makeup-air.

It is not a combustion-air calculation and not a closet 100 in² free-area drawing.

Makeup-air is hood-only vs 400. This page is the simultaneous sum ranking pages insist you must not forget.

Related calculators on this site:

How to use it

Leave dryer at 150 unless the listing is higher. Type hood high speed and bath fans that can run at the same time. Example is 150+400+50.

Dryer CFM (chips 125/150/200), hood CFM, bath CFM.

Values update in this browser as you type. Use Example for the same numbers as the worked section. Copy puts the result on the clipboard. Next links reuse the last CFM, ACH and temperatures you typed on this device.

Formula, units, and limits

Q_tot = dryer + hood + baths; makeup ≈ Q_tot if hood > 400 or dryer > 200

Reject zero or negative lengths, areas, flows, pressures and temperatures. This is a ranking-composite sketch, not a permit.

Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.

When you would use it

Typical uses include:

1) 150 CFM dryer + 400 CFM hood + 50 bath.

2) 900 CFM hood with the dryer on.

3) Dryer-only closet above 200 CFM.

None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.

Worked example

The Example button uses this set:

dryer 150 + hood 400 + baths 50 = 600 CFM

hood at the 400 talk → makeup ≈ 600 CFM

FAQ

Why 150 CFM?

It is the number ranking simultaneous-exhaust examples share when the listing is silent. Listings run 100–225.

Does the bath count?

If it can run with the hood and dryer, yes. Continuous 62.2 fans are a different question — ranking makeup examples often drop the smallest fan.

Infiltration credit?

Tight houses have little to give. This page does not subtract phantom leakage.

One makeup unit for kitchen and laundry?

Air has to arrive in the room that is exhausted, or through a real opening. Do not hide a laundry shortfall in the kitchen MAU.

Electric vs gas dryer?

Exhaust CFM is still exhaust CFM. Gas adds combustion air on another page.

Closet 100 in²?

A separate opening rule when the dryer lives in a closet. Not this sum.

References

Composite of ranking dryer and makeup pages: 150 CFM dryer default, 200 CFM dryer trigger, 400 CFM hood trigger, sum simultaneous fans.

  • ASHRAE Standard 62.1 and 62.2 — outdoor-air and dwelling-ventilation forms (overview of published identities; tables remain in the licensed standard).
  • International Mechanical Code — residential bath/kitchen exhaust discussion values commonly implemented as 50/20 CFM; confirm the adopted year.
  • ASHRAE Fundamentals — moist-air relations, duct fitting concepts, fan laws, hydronic constants 500 and 1.08.
  • ISO 14644-1 — cleanroom classification names (particle limits, not a mandatory ACH).
  • Magnus / WMO saturation vapor-pressure approximations for dew point.
  • Huebscher equivalent-diameter relation for rectangular ducts.

Disclaimer

Estimate only for dryer/simultaneous exhaust. Adopted IRC/IMC and a licensed designer prevail.

Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size refrigerant charge, fire dampers, medical gas, or electrical conductors.