1. Home
  2. Water
  3. Pipe friction (Hazen–Williams)

Pipe friction (Hazen–Williams) Calculator

Free Pipe friction (Hazen–Williams) calculator. Water friction hf/100 ft = 0.2083 (100/C)^1.852 Q^1.852 / d^4.8655, plus velocity. Runs in your browser; not a permit or a Manual J.

Updates in this browser · not a mechanical permit


Formula

Identity
hf/100 ft = 0.2083 (100/C)^1.852 Q^1.852 / d^4.8655; V = 0.4085 Q / ID²
Steps

Estimate only. Use the adopted mechanical code, nameplate curves and a licensed designer. Not Manual J, not a listed hood, not electrical sizing.

What this calculator does

Ranking hydronic friction calculators use Hazen–Williams in IP water units, not Darcy–Weisbach, because that is what sprinkler and hydronic worksheets share: hf per 100 ft = 0.2083 × (100/C)^1.852 × Q^1.852 / ID^4.8655. C chips 150 PVC / 140 copper / 130 steel / 120 aged. Velocity 0.4085 GPM / ID² sits next to it so you can still respect the 4 fps copper talk on hydronic-pipe. psi = ft / 2.31.

It is not a glycol viscosity correction and not a fitting-equivalent table (add those feet into L).

Hydronic-pipe picks Type L copper from a 4 fps cap. This page reports the feet of head that copper (or steel, or PVC) actually spends.

Related calculators on this site:

How to use it

Type GPM, inside diameter, C chip, length. Example is 15 GPM in 1 in Sch 40 (ID 1.049) at C 130, 100 ft.

GPM, ID inches, C chips 150/140/130/120, length ft.

Values update in this browser as you type. Use Example for the same numbers as the worked section. Copy puts the result on the clipboard. Next links reuse the last CFM, ACH and temperatures you typed on this device.

Formula, units, and limits

hf/100 ft = 0.2083 (100/C)^1.852 Q^1.852 / d^4.8655; V = 0.4085 Q / ID²

Reject zero or negative lengths, areas, flows, pressures and temperatures. This is a ranking-composite sketch, not a permit.

Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.

When you would use it

Typical uses include:

1) 15 GPM, 1.049 in ID, C=130, 100 ft.

2) Compare C 140 copper vs C 120 aged steel.

3) Feed pump-head with hf × circuit.

None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.

Worked example

The Example button uses this set:

15 GPM, ID 1.049, C=130, L=100

hf/100 from Hazen–Williams; V from 0.4085 Q/ID²

FAQ

C for copper?

New copper often 140–150 on those pages. 140 is the conservative chip here.

ID or nominal?

Hazen–Williams wants inside diameter. 1 in Sch 40 steel is 1.049 in, not 1.000.

psi vs feet?

Closed hydronic pumps are in feet. psi = ft / 2.31 for water.

Glycol?

Hazen–Williams is a water equation. Use Darcy–Weisbach with the right viscosity, or a manufacturer chart.

Fittings?

Add equivalent length into L. This page is straight pipe plus whatever length you typed.

2 in and up?

HW was fitted on larger water mains. Small-tube hydronic is still what ranking HVAC pages run.

References

Composite of ranking Hazen–Williams pages. Valid for water near 60 °F; hydronic 140–180 °F is a bit optimistic (lower viscosity).

  • ASHRAE Standard 62.1 and 62.2 — outdoor-air and dwelling-ventilation forms (overview of published identities; tables remain in the licensed standard).
  • International Mechanical Code — residential bath/kitchen exhaust discussion values commonly implemented as 50/20 CFM; confirm the adopted year.
  • ASHRAE Fundamentals — moist-air relations, duct fitting concepts, fan laws, hydronic constants 500 and 1.08.
  • ISO 14644-1 — cleanroom classification names (particle limits, not a mandatory ACH).
  • Magnus / WMO saturation vapor-pressure approximations for dew point.
  • Huebscher equivalent-diameter relation for rectangular ducts.

Disclaimer

Estimate only for water pipe friction. Hot-water viscosity, glycol and a licensed designer prevail.

Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size refrigerant charge, fire dampers, medical gas, or electrical conductors.