1. Home
  2. Air
  3. Commercial kitchen hood

Commercial kitchen hood Calculator

Free Commercial kitchen hood calculator. Type I unlisted wall or island canopy: Q = hood length × CFM per foot by cooking duty. Runs in your browser; not a permit or a Manual J.

Updates in this browser · not a mechanical permit


Formula

Identity
Q = L_hood × CFM/ft (wall 200/300/400/550; island 400/500/600/700)
Steps

Estimate only. Use the adopted mechanical code, nameplate curves and a licensed designer. Not Manual J, not a listed hood, not electrical sizing.

What this calculator does

Ranking commercial-hood calculators converge on IMC unlisted canopy rates by linear foot, not the residential 100/150 CFM/ft page. Wall-mounted canopy: 200 light / 300 medium / 400 heavy / 550 extra-heavy. Island canopy: 400 / 500 / 600 / 700. The heaviest appliance under the hood sets the rate. Makeup at ~80% of exhaust is the planning note they all add. Listed hoods use the listing instead.

It is not a listed-hood UL 710 worksheet, not NFPA 96, and not the residential kitchen-hood page.

Kitchen-hood is the home 100/150 CFM/ft plus BTU/100 rule. This page is the commercial linear-foot schedule.

Related calculators on this site:

How to use it

Type hood length in feet, wall vs island, duty of the heaviest appliance. Example is 10 ft wall, medium (fryers/griddles) = 3,000 CFM.

Hood length ft, wall vs island, duty light/medium/heavy/extra-heavy.

Values update in this browser as you type. Use Example for the same numbers as the worked section. Copy puts the result on the clipboard. Next links reuse the last CFM, ACH and temperatures you typed on this device.

Formula, units, and limits

Q = L_hood × CFM/ft (wall 200/300/400/550; island 400/500/600/700)

Reject zero or negative lengths, areas, flows, pressures and temperatures. This is a ranking-composite sketch, not a permit.

Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.

When you would use it

Typical uses include:

1) 10 ft wall canopy over fryers (medium → 300 CFM/ft).

2) Island over a charbroiler (heavy).

3) Solid fuel extra-heavy 550/700.

None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.

Worked example

The Example button uses this set:

10 ft wall, medium duty

Q = 10 × 300 = 3,000 CFM

makeup talk 80% = 2,400 CFM

FAQ

Light vs medium?

Ovens/steamers light; ranges/fryers/griddles medium; charbroilers/woks heavy; solid fuel extra-heavy — the duty names those pages share.

Listed hood?

Use the listed exhaust. These rates are the unlisted canopy floor.

Type II?

Heat and moisture without grease. Not this page’s Type I schedule.

Makeup 80 or 100%?

Planning pages show 80–90% so the kitchen stays slightly negative. IMC still wants makeup approximately equal to exhaust from all sources.

Overhang?

Code overhang lengthens the hood; type the actual hood length, not the appliance length.

Face velocity?

A check, not the sizing method these ranking pages use. Linear foot × duty is the code sketch.

References

Composite of ranking IMC hood-CFM pages. Overhang, backshelf and Type II dishwasher 100 CFM/ft are out of scope.

  • ASHRAE Standard 62.1 and 62.2 — outdoor-air and dwelling-ventilation forms (overview of published identities; tables remain in the licensed standard).
  • International Mechanical Code — residential bath/kitchen exhaust discussion values commonly implemented as 50/20 CFM; confirm the adopted year.
  • ASHRAE Fundamentals — moist-air relations, duct fitting concepts, fan laws, hydronic constants 500 and 1.08.
  • ISO 14644-1 — cleanroom classification names (particle limits, not a mandatory ACH).
  • Magnus / WMO saturation vapor-pressure approximations for dew point.
  • Huebscher equivalent-diameter relation for rectangular ducts.

Disclaimer

Estimate only for unlisted commercial hoods. IMC 507, the listing and a licensed designer prevail.

Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size refrigerant charge, fire dampers, medical gas, or electrical conductors.