1. Home
  2. Heat
  3. Baseboard from the room

Baseboard Heater Size Calculator

Free baseboard size calculator from room area. Watts = area × W/ft², with 12.5 percent more per foot of ceiling over 8. Length = watts / 250. Runs in your browser; not a permit.

Updates in this browser · not a mechanical permit


Formula

Identity
W = area × W/ft² × (1 + 0.125 × feet over 8); BTU/h = W × 3.412; length = W / 250
Steps

Estimate only. Use the adopted mechanical code, nameplate curves and a licensed designer. Not Manual J, not a listed hood, not electrical sizing.

What this calculator does

This page sizes electric baseboard from the room. An average room with an 8 ft ceiling uses 10 W/ft². A tight room uses 7.5, a drafty room 12.5, and very poor insulation can reach about 13. Each foot of ceiling above 8 ft adds 12.5 percent. Length uses about 250 W per foot. Size one room at a time.

Not a breaker, not a wire, and not a Manual J. The other baseboard page starts from BTU/h you already know.

This page stops at watts, BTU/h, and feet. Circuit amps stay off this site.

Related calculators on this site:

How to use it

Type room area, ceiling height, and W/ft². Chips are 7.5, 10, and 12.5. The example is a 150 ft² bedroom at 8 ft and 10 W/ft².

Room area ft², ceiling height ft, W/ft².

Values update in this browser as you type. Use Example for the same numbers as the worked section. Copy puts the result on the clipboard. Next links reuse the last CFM, ACH and temperatures you typed on this device.

Formula, units, and limits

W = area × W/ft² × (1 + 0.125 × feet over 8); BTU/h = W × 3.412; length = W / 250

Area, height, and W/ft² must be positive. Height at 8 ft has a factor of 1. Below 8 ft the factor stays 1.

Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.

When you would use it

Typical uses include:

1) 150 ft², 8 ft, 10 W/ft².

2) The same room at 7.5 or 12.5.

3) A 9 ft ceiling, factor 1.125.

None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.

Worked example

The example is a 150 ft² bedroom with an 8 ft ceiling:

150 × 10 × 1 = 1,500 W

1,500 × 3.412 = 5,118 BTU/h. Length = 1,500 / 250 = 6 ft.

FAQ

Why 10 W per ft²?

An average room with an 8 ft ceiling uses 10 W/ft². 7.5 is a tight room and 12.5 is a drafty one. Very poor insulation can reach about 13 W/ft².

Why 250 W per foot?

Electric baseboard is about 250 W per foot. 1,500 W is 6 ft. Hydronic output per foot is on the other baseboard page, where you type BTU/h per foot.

What does a 9 ft ceiling do?

Each foot of ceiling above 8 ft adds 12.5 percent. One extra foot is × 1.125. 150 ft² at 10 W/ft² becomes 1,688 W.

Where is the breaker?

Not on this page. It stops at watts, BTU/h, and length.

One room or the whole house?

One room at a time. Do not type the whole house into this box.

I already know the BTU/h?

Use the other baseboard page. It divides a known BTU/h by W/ft or BTU/h·ft.

References

An average 8 ft room uses 10 W/ft². 150 ft² is 1,500 W, 5,118 BTU/h, and 6 ft at 250 W/ft. A tight room uses 7.5 W/ft².

  • ASHRAE Standard 62.1 and 62.2 — outdoor-air and dwelling-ventilation forms (overview of published identities; tables remain in the licensed standard).
  • International Mechanical Code — residential bath/kitchen exhaust discussion values commonly implemented as 50/20 CFM; confirm the adopted year.
  • ASHRAE Fundamentals — moist-air relations, duct fitting concepts, fan laws, hydronic constants 500 and 1.08.
  • ISO 14644-1 — cleanroom classification names (particle limits, not a mandatory ACH).
  • Magnus / WMO saturation vapor-pressure approximations for dew point.
  • Huebscher equivalent-diameter relation for rectangular ducts.

Disclaimer

Room rule of thumb only. The heater listing and a room-by-room load control the install.

Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size refrigerant charge, fire dampers, medical gas, or electrical conductors.