1. Home
  2. Moisture
  3. Dew point

Dew point Calculator

Free Dew point Calculator. dew-point temperature from dry-bulb and relative humidity (or the reverse RH from DB and DP). Runs in your browser; not a permit or a Manual J.

Updates in this browser · not a mechanical permit


Formula

Identity
T_dp from e = RH/100 × e_s(T_db) inverted through Magnus
Steps

Estimate only. Use the adopted mechanical code, nameplate curves and a licensed designer. Not Manual J, not a listed hood, not electrical sizing.

What this calculator does

This page converts dew-point temperature from dry-bulb and relative humidity (or the reverse RH from DB and DP). It is the Dew point tool in the moisture group on ACH Calculator.

It is not a window-condensation CFD or a psychrometric chart. If you need those, open a related tool instead of stretching this identity.

The identity on screen is T_dp from e = RH/100 × e_s(T_db) inverted through Magnus. Adjacent pages keep their own inputs so you do not mix a bath-fan table with a 62.2 dwelling rate or a duct-friction takeoff.

Related calculators on this site:

How to use it

Use the fields that match the job: DB, RH or DP, result the other plus W. Press Example to load the worked numbers. Clear empties the form. Related tools in the Next bar reuse CFM, ACH, temperatures and flows you already typed on this device.

Values update in this browser as you type. Use Example for the same numbers as the worked section. Copy puts the result on the clipboard. Next links reuse the last CFM, ACH and temperatures you typed on this device.

Formula, units, and limits

T_dp from e = RH/100 × e_s(T_db) inverted through Magnus

Reject zero or negative lengths, areas, flows, pressures and absolute temperatures. ACH above about 120 is allowed for tents and cleanrooms but is flagged as unusual for occupied rooms. The 1.08, 0.68, 500 and 24 factors assume near-standard air or water; override density when you are in Denver or on glycol.

Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.

When you would use it

Typical uses include:

1) 75 °F 50% → DP ≈ 55 °F.

2) Coil DP vs room DP.

3) Basement condensation talk.

If the job is life-safety, sterile, or listed equipment, stop here and use the specification.

None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.

Worked example

The Example button uses this set:

T=75 °F

RH=50%

T_dp≈55.1 °F

Work the same arithmetic on paper; the live result should match within rounding.

FAQ

Magnus?

A published exponential fit for saturation vapor pressure. Good to ~0.1–0.5 °C in HVAC range.

DP vs WB?

DP is the saturation temperature at actual vapor pressure. WB includes evaporation cooling. Equal only at 100% RH.

Condensation on ducts?

If duct surface < DP of surrounding air. Insulation is the fix, not this number alone.

gr/lb?

Also shown via humidity-ratio.

Inside window?

Needs interior film T, not just room DP.

Next?

psychrometric for the full state.

References

Primary identity: T_dp from e = RH/100 × e_s(T_db) inverted through Magnus. Interpret it with the sources listed below, not as a photocopy of a copyrighted table.

  • ASHRAE Standard 62.1 and 62.2 — outdoor-air and dwelling-ventilation forms (overview of published identities; tables remain in the licensed standard).
  • International Mechanical Code — residential bath/kitchen exhaust discussion values commonly implemented as 50/20 CFM; confirm the adopted year.
  • ASHRAE Fundamentals — moist-air relations, duct fitting concepts, fan laws, hydronic constants 500 and 1.08.
  • ISO 14644-1 — cleanroom classification names (particle limits, not a mandatory ACH).
  • Magnus / WMO saturation vapor-pressure approximations for dew point.
  • Huebscher equivalent-diameter relation for rectangular ducts.

Disclaimer

Estimate only for Dew point. Adopted mechanical codes, OEM curves and a licensed designer prevail.

Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size refrigerant charge, fire dampers, medical gas, or electrical conductors.