1. Home
  2. Duct
  3. Friction rate from ESP

Friction rate from ESP Calculator

Free Friction rate from ESP calculator. Available static pressure after coil, filter and fittings, then FR = ASP × 100 / TEL. Runs in your browser; not a permit or a Manual J.

Updates in this browser · not a mechanical permit


Formula

Identity
ASP = ESP − ΣΔP; FR = ASP × 100 / TEL
Steps

Estimate only. Use the adopted mechanical code, nameplate curves and a licensed designer. Not Manual J, not a listed hood, not electrical sizing.

What this calculator does

Ranking Manual D friction-rate pages all do two subtractions: ASP = blower ESP minus coil, filter, registers and other external drops; TEL = longest supply plus longest return equivalent length; FR = ASP × 100 / TEL in inches w.c. per 100 ft. They also flag the 0.06–0.18 working band. Defaults 0.5 ESP, 0.20 coil, 0.10 filter, 0.06 terminals, 150+100 ft TEL are the numbers those pages repeat.

It is not a fitting-equivalent-length table and not a blower curve. Type OEM drops at your airflow.

The duct-friction page spends a rate you already know. This page is how that rate is born from the blower budget.

Related calculators on this site:

How to use it

Leave ESP at 0.5 unless the fan table says otherwise. Subtract only losses outside the rating boundary. Example uses 0.36 in of components over 250 ft TEL.

ESP, coil ΔP, filter ΔP, other ΔP, supply TEL, return TEL.

Values update in this browser as you type. Use Example for the same numbers as the worked section. Copy puts the result on the clipboard. Next links reuse the last CFM, ACH and temperatures you typed on this device.

Formula, units, and limits

ASP = ESP − ΣΔP; FR = ASP × 100 / TEL

Reject zero or negative lengths, areas, flows, pressures and temperatures. This is a ranking-composite sketch, not a permit.

Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.

When you would use it

Typical uses include:

1) 0.5 in ESP, wet coil 0.20, filter 0.10, 0.06 terminals.

2) Negative ASP — components ate the blower.

3) Short ducts that push FR above 0.18.

None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.

Worked example

The Example button uses this set:

ESP=0.5; coil 0.20; filter 0.10; other 0.06

TEL=150+100=250 ft

ASP=0.14; FR=0.056 in/100 ft

FAQ

What is TEL?

Straight duct plus fitting equivalent lengths on the controlling supply path plus the controlling return path. Parallel branches are not added.

0.08 in/100 ft?

A field habit. This page derives the rate instead of assuming 0.08.

Coil inside the rating?

If the fan table already includes the coil, do not subtract it again.

Negative ASP?

The components consume the blower. Change the filter, coil, route, or equipment before sizing duct.

0.06 to 0.18?

The working window ranking Manual D pages all cite. Below 0.06 the ducts get huge; above 0.18 they get noisy.

Measured TESP?

Diagnosis, not design. Design uses rated ESP at the design CFM.

References

Composite of ranking ASP÷TEL calculators. Component drops are user-typed, not reprinted from Manual D tables.

  • ASHRAE Standard 62.1 and 62.2 — outdoor-air and dwelling-ventilation forms (overview of published identities; tables remain in the licensed standard).
  • International Mechanical Code — residential bath/kitchen exhaust discussion values commonly implemented as 50/20 CFM; confirm the adopted year.
  • ASHRAE Fundamentals — moist-air relations, duct fitting concepts, fan laws, hydronic constants 500 and 1.08.
  • ISO 14644-1 — cleanroom classification names (particle limits, not a mandatory ACH).
  • Magnus / WMO saturation vapor-pressure approximations for dew point.
  • Huebscher equivalent-diameter relation for rectangular ducts.

Disclaimer

Estimate only for friction rate from ESP. ACCA Manual D, OEM curves and a licensed designer prevail.

Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size refrigerant charge, fire dampers, medical gas, or electrical conductors.