Free Indoor pool CFM Calculator. a crude indoor-pool exhaust/OA sketch from water area and a CFM/ft²-class factor you type. Runs in your browser; not a permit or a Manual J.
Estimate only. Use the adopted mechanical code, nameplate curves and a licensed designer. Not Manual J, not a listed hood, not electrical sizing.
This page converts a crude indoor-pool exhaust/OA sketch from water area and a CFM/ft²-class factor you type. It is the Indoor pool CFM tool in the moisture group on ACH Calculator.
It is not ASHRAE HVAC Applications pool chapter reprint, a chemical off-gassing model, or a natatorium psych chart. If you need those, open a related tool instead of stretching this identity.
The identity on screen is CFM ≈ rate × A_water × humidity_factor (user rate; sketch). Adjacent pages keep their own inputs so you do not mix a bath-fan table with a 62.2 dwelling rate or a duct-friction takeoff.
Related calculators on this site:
Use the fields that match the job: Water area, air and water T, RH target, CFM/ft² chip, result CFM and latent sketch. Press Example to load the worked numbers. Clear empties the form. Related tools in the Next bar reuse CFM, ACH, temperatures and flows you already typed on this device.
Values update in this browser as you type. Use Example for the same numbers as the worked section. Copy puts the result on the clipboard. Next links reuse the last CFM, ACH and temperatures you typed on this device.
Q_OA ≈ 0.48 CFM/ft² × A_water (62.1-style talk;
Reject zero or negative lengths, areas, flows, pressures and absolute temperatures. ACH above about 120 is allowed for tents and cleanrooms but is flagged as unusual for occupied rooms. The 1.08, 0.68, 500 and 24 factors assume near-standard air or water; override density when you are in Denver or on glycol.
Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.
Typical uses include:
1) 20×40 ft pool, 0.5 CFM/ft² talk.
2) Residential spa.
3) Dehumidifier vs outdoor air.
If the job is life-safety, sterile, or listed equipment, stop here and use the specification.
None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.
The Example button uses this set:
A=800 ft²
0.48 CFM/ft²
OA CFM=384
Work the same arithmetic on paper; the live result should match within rounding.
It is a discussion chip. Real natatorium design uses evaporation formulas (activity factor, vapor-pressure difference). Type a better rate if you have one.
Unoccupied vs splashing changes evaporation a lot. Not a single CFM.
Need source capture / higher exhaust, not just RH control.
Keep room DP below glass T. dew-point page.
Pool halls are latent monsters. dehumidifier vs OA is an economic choice.
Still a sketch. A listed enclosure dehumidifier OEM is better.
Primary identity: CFM ≈ rate × A_water × humidity_factor (user rate; sketch). Interpret it with the sources listed below, not as a photocopy of a copyrighted table.
Estimate only for Indoor pool CFM. Adopted mechanical codes, OEM curves and a licensed designer prevail.
Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size refrigerant charge, fire dampers, medical gas, or electrical conductors.