Air-change and room CFM calculators

Room ACH, bath fans, 62.1/62.2, makeup air and CADR.

Air

ACH to CFMRoom air changes per hour into supply or exhaust airflow in cubic feet per minute (and the reverse).Bathroom fan CFMA residential bathroom exhaust rate using the IMC-style 50/20 CFM chips or a volume×ACH check.Range hood CFMRange-hood airflow from hood length, face velocity, or a typed CFM — not from kitchen ACH.ASHRAE 62.2A dwelling mechanical ventilation rate using the ASHRAE 62.2 floor-area plus bedroom count identity.ASHRAE 62.1 OABreathing-zone outdoor air from 62.1 people and area rates you type (Rp, Ra, Pz, Az).Makeup airHow much dedicated makeup airflow you still need after subtracting the exhaust you typed and an allowed uncompensated amount.Garage exhaustA residential or small garage exhaust sketch from ACH or CFM per square foot.Attic ventilationA net-free attic ventilation area sketch using 1/150 or 1/300 of attic floor area.Cleanroom ACHCleanroom supply CFM from a user-selected air-change target associated with an ISO class name.Grow tent CFMGrow-tent exhaust from tent volume, a target air-change rate, and an optional carbon-filter derate.CADR air changesAir-cleaner air changes from AHAM-style CADR and room volume (or the reverse CADR need).ACH50 to ACHA crude natural infiltration estimate from a blower-door ACH50 and a user n-factor.Parking garage CFMAn enclosed parking-garage exhaust sketch from ACH or CFM per area — with CO demand-control called out as not modeled.CFM per roomSplit system CFM across rooms by weighted floor area, then count registers at 120 CFM each.Commercial exhaust CFMRoom exhaust from a user-typed per-fixture or per-area rate — not a reprinted occupancy table.Commercial kitchen hoodType I unlisted wall or island canopy: Q = hood length × CFM per foot by cooking duty.Dryer exhaust and makeupAdd dryer + hood + baths that can run together; flag makeup when the hood > 400 or the dryer > 200 CFM.Whole-house fanCFM = floor area × CFM/ft², scaled by ceiling height over 8 ft. Attic net free area is CFM/750.Evaporative coolerCFM = (floor area × ceiling height) / minutes per air change.Attic fanCFM = attic floor × 0.7, or × 0.805 for a dark or steep roof.CO₂ to CFMOutdoor CFM per person = generation / ((indoor ppm − outdoor ppm) / 1,000,000).ERV / HRV heatVentilation from floor area and bedrooms, then recovered heat = 1.08 × CFM × ΔT × effectiveness.

What this calculator does

This group converts room ACH, bath exhaust, kitchen hoods, ASHRAE 62.2 whole-house air, 62.1 outdoor air, makeup air, CADR, ACH50 and related exhaust sketches into a flow you can take to a fan or a duct.

It is not a duct sizer and not a coil load. Each card is one identity: do not add bath 50 CFM to a 62.2 dwelling rate unless the design says so.

How to use it

Open ACH to CFM for a box. Open bathroom-fan for IMC-style 50/20. Open whole-house for 62.2, outdoor-air for people+area, kitchen-hood for capture, makeup-air when exhaust is large.

Type the room or occupancy the page asks for. Example on each tool matches that page’s worked section.

Formula, units, and limits

Room: CFM = ACH × V / 60. Bath chips: 50 CFM intermittent / 20 continuous. 62.2: Q = (CFA × 0.03) + 7.5(Nbr+1) plus infiltration options. 62.1: Vbz = Rp×Pz + Ra×Az. Hood: Q ≈ 100 CFM per foot or face velocity × area.

Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.

When you would use it

Use air tools when the unknown is outdoor air or exhaust CFM. Use duct tools when you already have CFM and need size or pressure.

None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.

Worked example

12×14×8 ft at 6 ACH → 134.4 CFM on ACH to CFM. A 5×8×8 ft bath at 50 CFM is about 9.4 ACH — the table, not the ACH, usually governs.

A 2,000 ft², 3-bedroom dwelling 62.2 sketch is on whole-house, not on this group’s ACH card.

FAQ

ACH or 62.2?

ACH is a room rate. 62.2 is a dwelling outdoor-air form. They share CFM and almost never the same equation.

Hood versus kitchen ACH?

A hood captures at the cooktop. Diluting the whole kitchen does not replace capture velocity.

Makeup air?

Open makeup-air when several baths plus a hood exceed the local threshold, not for a single 50 CFM fan.

CADR?

CADR is cleaner CFM for a portable filter, not outdoor air.

Cleanroom ACH?

ISO class names are discussion ranges, not particle limits. Use the spec.

Parking garage?

That page is a ventilation sketch, not a CO-system design.

References

Disclaimer

Exhaust tables and 62.1/62.2 forms are estimates. Adopted code year and a licensed designer prevail.

Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size combustion air, refrigerant charge, fire dampers, medical gas, or electrical conductors.