Free ACH to CFM Calculator. room air changes per hour into supply or exhaust airflow in cubic feet per minute (and the reverse). Runs in your browser; not a permit or a Manual J.
Estimate only. Use the adopted mechanical code, nameplate curves and a licensed designer. Not Manual J, not a listed hood, not electrical sizing.
This page converts room air changes per hour into supply or exhaust airflow in cubic feet per minute (and the reverse). It is the ACH to CFM tool in the air group on ACH Calculator.
It is not a Manual J load, a duct friction takeoff, or an ASHRAE 62.2 whole-dwelling vent rate. If you need those, open a related tool instead of stretching this identity.
The identity on screen is CFM = ACH × Volume / 60. Adjacent pages keep their own inputs so you do not mix a bath-fan table with a 62.2 dwelling rate or a duct-friction takeoff.
Related calculators on this site:
Use the fields that match the job: Length, width, height (or a typed volume), ACH, and CFM. Fill any consistent set; the other quantity solves. Unit chips switch feet/metres and CFM / m³/h / L/s. Press Example to load the worked numbers. Clear empties the form. Related tools in the Next bar reuse CFM, ACH, temperatures and flows you already typed on this device.
Values update in this browser as you type. Use Example for the same numbers as the worked section. Copy puts the result on the clipboard. Next links reuse the last CFM, ACH and temperatures you typed on this device.
CFM = ACH × Volume / 60
Reject zero or negative lengths, areas, flows, pressures and absolute temperatures. ACH above about 120 is allowed for tents and cleanrooms but is flagged as unusual for occupied rooms. The 1.08, 0.68, 500 and 24 factors assume near-standard air or water; override density when you are in Denver or on glycol.
Inch-pound identities (CFM, ft, in. w.g., BTU/h, GPM) are the US HVAC default. SI chips use m³/h or L/s, metres, Pa, kW and L/s. 1 CFM ≈ 1.699 m³/h ≈ 0.472 L/s. 1 in. w.g. ≈ 249 Pa. Air density 0.075 lb/ft³ and the 1.08 / 0.68 / 500 / 24 factors assume near-standard air or water unless you override them.
Typical uses include:
1) A 12×14×8 ft bedroom at 6 ACH before picking a bath fan.
2) An open office using 4 ACH as a sketch before 62.1 outdoor air.
3) A grow tent volume converted to CFM before a carbon-filter derate.
If the job is life-safety, sterile, or listed equipment, stop here and use the specification.
None of these sketches replace a licensed mechanical engineer, a Manual J/D/S, a listed-hood submittal, or the mechanical code adopted on the job. Cleanrooms, health-care, and fire/smoke exhaust need those specifications.
The Example button uses this set:
12 ft × 14 ft × 8 ft
volume 1344 ft³
6 ACH
CFM = 6 × 1344 / 60 = 134.4 CFM
Work the same arithmetic on paper; the live result should match within rounding.
The identity uses room volume and ACH. A fan nameplate is at a stated static pressure; a duct traverse is what the room actually gets. Use the fan-actual and static-pressure tools for pressure.
ACH is changes per hour. CFM is cubic feet per minute. 60 minutes per hour converts the same volume flow.
It is a design choice, not a universal constant. Baths, offices, grow tents and cleanrooms use different ranges. Open the room-ACH chart, then come back.
Yes. The engine converts to cubic feet internally or reports m³/h. The formula is the same: Q = ACH × V / time.
No. ACH here is mechanical air changes of the typed volume. ACH50 / n is a separate infiltration sketch.
Volume is small. Half an air change on 800 ft³ is only about 7 CFM. That can still be a 62.2 whole-house number, not a bath exhaust.
Primary identity: CFM = ACH × Volume / 60. Interpret it with the sources listed below, not as a photocopy of a copyrighted table.
Estimate only for ACH to CFM. Adopted mechanical codes, OEM curves and a licensed designer prevail.
Results are estimates computed on your device. Nameplate curves, TAB measurements, and the authority having jurisdiction control the installation. This site does not size refrigerant charge, fire dampers, medical gas, or electrical conductors.